ALLEN & HEATH Xone 02 0 2 DJ Mixer 2 x stereo ch NEW

From inputs to outputs, we created Xone:02 to be the world’s greatest battle / scratch mixer. Every fader is a deluxe VCA design, they’re all reversible, they all have

contour controls and they can all be easily replaced by removing the steel faceplate. We’ve kept the fader area clear for action and we’ve kept controls like pan and

EQ out of the way on low profile sliders. Even the transform switches can be rotated to work the way you like them.

2 Dual Stereo Channels

Channels have RIAA [RCA] inputs, switchable to line, plus stereo line level inputs [RCA], each with gain control. Powerful 3 band ‘music’ EQ on sliders. High quality

45mm faders. Input reverse switch for battle mixing. Pre fade monitoring on 12 segment 3 colour peak reading bar meters

Mic Channel

2 XLR inputs with separate gain controls, on switch and 3 band EQ with HPF. Routes direct to mix outputs. FX insert on button

Stereo Mix Outputs

Balanced mix outputs on XLR with multi-point VCA level master control. The mix output level can be displayed on the 12 segment 3 colour peak reading bar meters

Booth Output

RCA outputs with level control for booth / link out to additional ‘daisy-chain’ mixers

FX Loop

Channels have an effect loop on switch with silent FET switching. Effect insert points are separate [TRS] inputs and outputs

3 Band EQ

Powerful 3 band 12dB/oct EQ with ëasymmetricí characteristic: +6dB boost emphasis and -26dB cut for frequency band elimination

Penny&Giles VCA Crossfader

Ultra-high quality Penny & Giles conductive plastic crossfaders come as standard on the Xone:02. The 45mm faders contour control, reverse switch and led.

Replacement of crossfaders is easy - it takes only minutes to remove the faceplate and replace the fader unit

Transform Switches

Performance channel mute controls which can be rotated to work up/down or left / right

Engineer / DJ’s Toolbox

High powered headphone output with level and mute switch. Booth / link output on TRS with level. 12 segment 3 colour bar metering displays CH1&2 or mix. Channels

have 12 segment 3 colour bar meters. CH1 / CH2 cue fader allows preview of x-fades

Options

Conductive plastic Penny & Giles x-fader

Connections

INPUTS 

Turntable RCA RIAA Equalisation (Switch-able toline) 2-140mV 47K/330pF

Line RCA >8k2 ohms -15 / +22 dBu

Effect Return TRS jack 10k ohms 0dBu

Link IN RCA 10k ohms 0dBu

MIC  XLR <2k ohms Balanced -10 / -50dBu

OUTPUTS 

Main OUT XLR <47 ohms Balanced 0dBu

Effect Send TRS jack 47 ohms Impedance Balanced 0dBu

Link/Booth RCA 47 ohms 0dBu

Headphones 30-600 ohms, 75ohms recommended, Jack, Tip =left, Ring = right 500mW RMS into 47 ohms  

Technical Specifications

OdBu = 0.775 Volts rms +4dBu = 1.23V rms

OdBu = 1 Volt rms -10dBV = 316mV rms

Maximum output level

MAIN OUT +23dBu into >2K ohm load

EFFECT SEND +21dBu into >2K ohm

LINK/BOOTH +21dBu into >2K ohm

Internal headroom

Channels +21dBu

Mix to output +23dBu

Peak indicators meters

12bar peak reading Peak on 8dB before clipping

Frequency response

20Hz-30kHz 0/-1dB

Distortion THD+noise measured at +10dBu 1kHz

0.04%

Crosstalk channel shutoff measured at 1kHz

<90dB

MIC EI Measured with 150ohm load

129dB

Residual output noise - non weighted 22Hz-22kHz filter

<88dBu

Mix noise - non weighted 22Hz-22kHz filter

<-81dBu

Power Supply Internal switch mode power unit with auto sensing mains input.

Mains In socket IEC 3 pin

AC Mains 100-240V AC 50/60Hz

Power lead Country dependent

Consumption 30W max

Fuse Rating T500mA 20mm

Internal power rails +/- 16volts