8x6 STEEL METAL SHED BIKE SHEDS GARDEN STORAGE 8 x6 NEW

Click Below to see:

Range of Metal Sheds

Sheds Without Windows

Sheds with Windows
Patio Furniture
Garden Storage

-----BRAND NEW-----

STRONG LASTING STEEL METAL SHED

8' x 6'

Picture shows 8 x 7

The 8' wide metal shed offers several benefits over typical 'thin clad metal sheds' with its 1.78m (5'10") greater eaves height, along with being constructed from hot-dipped galvanised steel throughout - hence the manufacturers 12 year 'no rust perforation' warranty.

Ventilated gables are also included as standard.
Painted inside and out in contrasting dark green / light grey / white combination, this product should suit most gardens.
Requiring no maintenance (no cracks, warps, rot & rodent proof), access is provided by the 1.70m high x 1.04m wide double sliding doors (fitted internally, secured with a padlock - not supplied), complete with a full width strong door entry / exit ramp. Where a level concrete or paved base exists (as no floor is supplied) please select the Hilti Screw kit (includes drill bit), to secure the building to your base. See below for pricing of other optional extras  (skylight, sliding window and shelving).

Screwed self assembly only, instructions supplied. Flat-pack, component format.

·        HOT- DIPPED GALVANISED STEEL CONSTRUCTION THROUGHOUT

·        12 YEAR ‘NO RUST PERFORATION’ GUARANTEE

·        EXTRA HIGH WALLS – 178 cm EAVES HEIGHT

·        VENTILATED GABLES AS STANDARD TO ALL MODELS

·        NO CRACKS OR WARPS

·        ROT AND RODENT PROOF STORAGE

·        STRAIGHTFORWARD ASSEMBLY WITH FULL INSTRUCTIONS

·        STRONG EXIT / ENTRY RAMP ACROSS THE FULL DOOR OPENING WIDTH

·        A GOOD RANGE OF OPTIONAL ACCESSORIES AVAILABLE

·        DEDICATED HOME DELIVERY SERVICE, WITH PRE-BOOKED DELIVERIES

It is essential that the buildings are anchored to a suitable concrete or slab base. Full details on preparing a base for these buildings will be sent prior to the unit being delivered. Nominal Model sizes are based on roof dimensions. Please refer to the table below for accurate roof and base

Window Kit - Add £29 (each)

3mm thick two piece sliding Acrylic window. Can be fitted to any Canberra model, except Canberra Low Pent 6x4. Approximately 61.5cm x 33cm (width x height). Kit supplied complete with ready cut down wall panel to make fitting a simple task

One piece corner shelf - Add £14

Galvanised triangular shelf section, which fixes simply to the top of the mid wall brace of the shed. A simple and economic item which can be used in either, or both of the two rear corners of the shed.

Three piece corner shelf - Add £35

Galvanised triangular corner shelves, complete with support rails and fittings. Simple fitting, and providing a good area of storage space within a small area, helping to safely store all those small items.

Single rear wall shelf – Add £39

A strong height adjustable shelf section designed to fit across the full width of the rear of your chosen shed. Comes complete with all braces and fittings, and is covered by 12mm thick MDF shelving board. Provides spacious and secure shelving to increase the storage capacity of your shed.

Double rear wall shelf – Add £65

Two strong height adjustable shelf sections designed to fit across the full width of the rear of your chosen shed. Comes complete with all braces and fittings, and are covered by 12mm thick MDF shelving board. Provides spacious and secure shelving to increase the storage capacity of your shed.

Skylight – Add £19

A translucent roof sheet which completely replaces a full metal roof panel, and permits plenty of daylight to enter the shed interior, whilst preventing visual identification of items stored inside

Hilti kit- Add £12

A complete kit containing the correct number of fasteners to anchor your shed, plus a free masonry drill bit to drill into your concrete or flagstone base. After construction of the shed is complete, simply position the shed in it’s final position, drill down through the pre-punched anchor holes in the inside of the base rail and simply hammer in the fasteners. The heads have cross recess slots to enable removal at a later date if required.

Timber floor – Please email sherwood_trading@btinternet.com for price

This timber floor kit is constructed from fully pressure treated timbers for long maintenance free life. The floor boards are constructed from 19mm thick half lapped timber, and are mounted onto 50mm x 25mm sawn bearers. Nails are provided for assembly of the kit, as well as screws and washers for securing the shed base rails to the top surface of the floor. The floor can then be secured down to a hard standing with brackets and screws, or onto level well drained land with timber pegs (neither supplied).

Delivery to mainland UK and excludes some parts of Scotland (if unsure please email your post code to sherwood_trading@btinternet.com).

We operate a system of pre-booked delivery days, with a good estimate given as to an AM or PM arrival of our vehicle. This is arranged approximately one week ahead of the actual delivery day.
When you place an order a confirmation is raised within 48 hours and is sent to you giving an expected week commencing date for delivery.  In the week prior to that expected week you will be contacted by telephone by manufacturer’s logistics department to arrange an actual delivery day.

Lead time is approximately 15 working days.